Fisher and Paykel Dishwasher Dishdrawer Error Code F9 Error Code Cause: Electrical Malfunction. How To Fix: Turn power to DishDrawer off then turn on power supply. If the display is showing an F fault code, you may be able to clear the fault by resetting the dishwasher - see the steps below. If the fault persists, note down the code before disconnecting the dishwasher from the water and power supplies and Contact Customer Care. To attempt to clear the F fault code Press to stop the beeping.

How to mend anything. Free repair help Kitchen Appliances, Dishwashers - f9 fault fisher paykel dd605.

CDA Dishwasher Error F1

This refers to an NTC sensor fault , excessively high or excessively lower temperature of the water during the wash cycle, or a fault in the wiring loom.

CDA Dishwasher Error F2

The safety device in the base of the appliance has been operated by a water leak.

The drain pump operates automatically when the anti flood device is activated , also the water valve is switch off

CDA Dishwasher Error F3

The heating cycle is not working. This can occur if the heater heats up too slowly or if the heating element is open circuit.

• A number of other components can also be the cause of this fault;
• A defective electronic pcb
• A fault ntc sensor or a broken wiring loom

CDA Dishwasher Error F4

Water fails to drain within a predetermined time period and the water level indicator senses that water is still in the sump of the dishwasher.

This fault can be caused by a blockage or failure of the drain pump. A faulty water level indicator can also be the cause of the fault

CDA Dishwasher Error F5

Inadequate water supply.

Fisher Paykel Dishwasher Troubleshooting Guide

What to do:

• Make sure the water tap is fully open
• Close the water tap, separate the water inlet hose from the tap and clean the filter.
• Restart the dishwasher.
• If the error continues, contact CDA Customer Care

CDA Dishwasher Error F6

No flow of water into the appliance is being recorded by the flow meter.
The causes of this can be an open circuit inlet solenoid valve or a restriction in the water supply to the appliance.

CDA Dishwasher Error F7

This is an indication of a flow meter failure

CDA Dishwasher Error F8

The incorrect water level during any part of the washing cycle. A slow running wash motor causing low water pressure, internal blockages or over sudsing can create this fault code.

CDA Dishwasher Error F9

The dishwasher fills with too much water.

The water valve might not close allowing water constantly to flow into the dishwasher.

A defective control pcb may also be the cause of this fault.

CDA Dishwasher Error FA

The pressure sensing device or water indicator does not switch

Fisher Paykel dishwashers are designed to make doing the dishes easy! New ranges bring an air of sophistication to any kitchen – allowing flexible washing options as you wash one drawer and stack the other.

Fisher & Paykel F9 Manuals

Sanitise mode kills 99.9% of bacteria, and flexible racking lets you customise internal shelves to suit your needs. But what happens when things go wrong? Look at some Fisher Paykel dishwasher problems and troubleshooting here…

Fisher and Paykel Error Codes

Fisher Paykel dishwasher fault codes will help you determine the nature of the fault – but you may need a qualified engineer to repair or replace relevant parts. See a range of fault codes and their meanings below:

• Fisher Paykel dishwasher fault code F1 – this indicates that the flood switch has been activated for more than six seconds
• Fault Code F2 – motor rotation hasn’t been detected
• Fault Code F3 – water temperature has reached over 85 degrees Celsius
• Fault Code F4 – the element is energised but the temperature isn’t increasing
• Fault Code F5 – this is an error with the lid that could involve the lid lock switch
• Fault Code F8 – an electrical issue which may relate to a reset error
• Fault Code F9 – electronics failure

U Error Codes

• Error Code U1 – the dishwasher has failed to fill with water after about three minutes
• Error Code U2 – this indicates a loading error
• Error Code U4 – drawer faults are the problem here
• Error Code U6 – a spray arm issue has been detected

Fisher Paykel Dishwasher Troubleshooting

Fault Codes - Fisher & Paykel Product Help

Fisher and Paykel dishwasher troubleshooting problems may be linked to:

Fisher Paykel dishwasher drain problems – this can cause water leaking issues. The drain hose may have become disconnected from the waste pipe, or the water inlet hose isn’t properly connected. Excess water in the drawer could indicate the drain hoses are kinked or damaged.

Fisher Paykel dishwasher not starting – this could be related to issues with the power supply, power switches, fuses, or the circuit breaker. Any electrical faults need to be safely inspected by a qualified appliance repair technician. Other difficulties could lie with a drawer or the door being unable to close properly, a snag with the child-lock feature, or depressed buttons that won’t release.

Fisher Paykel dishwasher making noises – knocking or rattling sounds during the wash indicate that a spray arm is knocking against the dishes and needs to be repositioned. With some models continuous or intermittent beeping warn that a fault has occurred – a programme may be in pause mode – but if this continues you’ll need to get expert help to diagnose and fix any ongoing issues.

Fisher Paykel dishwasher motor issues – if the controller is unable to sense the motor rotating this could down to a number of reasons. A foreign object may have jammed the rotor, or there may be a wiring fault within the hall sensor or the controller. A defective electronic controller, PCB main filter, or motor stator winding will all need to be dealt with by an expert.

Fisher and Paykel dishwasher problem solving will often be determined by the model of your appliance. For instance, Fisher Paykel dishwasher DD603 problems may include an activated flood switch, motor problems, failed temperature sensor, faulty element, or electronics malfunction.

Refer to the fault codes above to identify the source of the problem – all of these faults can be identified and repaired by your local professionals.

Get Experienced Appliance Repairers

Fisher Paykel dishwasher repair London specialists will use advanced tools and equipment to quickly and effectively get your dishwasher up and running. Highly trained technicians will locate the source of any issues and fix them for you. You’ll get a fully insured service – all delivered with a six-month quality guarantee.